|
Question : Problems with Bonded T-1
|
|
We just acuired a bonded 2xT1. I have configured a Cisco 2811 with a Dual T1/CSU card. After rebooting the Router my serial interface is up but the protocol keeps coming down. I have included the show tech-support file for the guru's to see if I am doing something wrong here.
------------------ show version ------------------
Cisco IOS Software, 2800 Software (C2800NM-IPBASE-M), Version 12.3(8)T8, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Wed 06-Apr-05 16:46 by yiyan
ROM: System Bootstrap, Version 12.3(8r)T7, RELEASE SOFTWARE (fc1)
ypcnm.com uptime is 1 week, 3 days, 17 hours, 59 minutes
System returned to ROM by reload at 22:11:50 UTC Mon Dec 19 2005
System image file is "flash:c2800nm-ipbase-mz.123-8.T8.bin"
Cisco 2811 (revision 53.51) with 253952K/8192K bytes of memory.
Processor board ID FTX0933A11M
2 FastEthernet interfaces
2 Serial interfaces
2 Channelized T1/PRI ports
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
62720K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
------------------ show running-config ------------------
Building configuration...
Current configuration : 2581 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
no service dhcp
!
hostname removed
!
boot-start-marker
boot-end-marker
!
logging buffered 51200 warnings
enable secret 5
enable password
!
username removed privilege 15 secret 5
username removed privilege 15 view root secret 5
username removed privilege 15 view root secret 5
no network-clock-participate wic 0
no network-clock-participate aim 0
no network-clock-participate aim 1
no aaa new-model
ip subnet-zero
no ip source-route
!
!
ip cef
!
!
no ip domain lookup
no ftp-server write-enable
!
controller T1 0/0/0
framing esf
linecode b8zs
channel-group 0 timeslots 1-24 speed 64
!
controller T1 0/0/1
framing esf
linecode b8zs
channel-group 0 timeslots 1-24 speed 64
!
interface FastEthernet0/0
description Test Outside-Public
ip address 12.196.245.129 255.255.255.252
no ip redirects
no ip unreachables
no ip proxy-arp
no ip mroute-cache
duplex full
speed auto
no cdp enable
no mop enabled
!
interface FastEthernet0/1
description management-interface
ip address 10.10.10.1 255.255.255.248
duplex auto
speed auto
no cdp enable
!
interface Serial0/0/0:0
description Circuit ID:DHEC187035.802
bandwidth 1536
ip address 12.125.97.94 255.255.255.128
no ip redirects
no ip unreachables
no ip proxy-arp
ip load-sharing per-packet
encapsulation ppp
no cdp enable
!
interface Serial0/0/1:0
description Circuit ID:DHEC187035.801
bandwidth 1536
ip address 12.124.244.26 255.255.255.128
no ip redirects
no ip unreachables
no ip proxy-arp
ip load-sharing per-packet
encapsulation ppp
no cdp enable
!
ip classless
ip route 0.0.0.0 0.0.0.0 Serial0/0/0:0
ip route 0.0.0.0 0.0.0.0 Serial0/0/1:0
ip http server
ip http authentication local
ip http timeout-policy idle 600 life 86400 requests 10000
!
snmp-server community RW
snmp-server enable traps tty
no cdp run
!
control-plane
!
line con 0
login local
line aux 0
line vty 0 4
privilege level 15
password
login local
transport input telnet
line vty 5 15
privilege level 15
password
login local
transport input telnet
!
scheduler allocate 20000 1000
!
end
------------------- show interfaces ------------------
FastEthernet0/0 is up, line protocol is down
Hardware is MV96340 Ethernet, address is 0014.f201.2420 (bia 0014.f201.2420)
Description: Test Outside-Public
Internet address is 12.196.245.129/30
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, Auto Speed, 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last input 1w2d, output 00:00:05, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
245 packets input, 21516 bytes
Received 125 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog
0 input packets with dribble condition detected
92863 packets output, 5571780 bytes, 0 underruns
0 output errors, 0 collisions, 4 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
FastEthernet0/1 is up, line protocol is down
Hardware is MV96340 Ethernet, address is 0014.f201.2421 (bia 0014.f201.2421)
Description: management-interface
Internet address is 10.10.10.1/29
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Auto-duplex, Auto Speed, 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last input 1w2d, output 00:00:07, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
245 packets input, 21516 bytes
Received 125 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog
0 input packets with dribble condition detected
94411 packets output, 5690976 bytes, 0 underruns
0 output errors, 0 collisions, 3 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
Serial0/0/0:0 is up, line protocol is down
Hardware is GT96K Serial
Description: Circuit ID:DHEC187035.802
Internet address is 12.125.97.94/25
MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, LCP REQsent, loopback not set
Keepalive set (10 sec)
Last input never, output 00:00:01, output hang never
Last clearing of "show interface" counters 1w3d
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 1152 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
8 input errors, 8 CRC, 0 frame, 0 overrun, 0 ignored, 8 abort
185101 packets output, 2591414 bytes, 0 underruns
0 output errors, 0 collisions, 18509 interface resets
0 output buffer failures, 0 output buffers swapped out
2 carrier transitions
Timeslot(s) Used:1-24, SCC: 0, Transmitter delay is 0 flags
Serial0/0/1:0 is up, line protocol is down
Hardware is GT96K Serial
Description: Circuit ID:DHEC187035.801
Internet address is 12.124.244.26/25
MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, LCP REQsent, loopback not set
Keepalive set (10 sec)
Last input never, output 00:00:00, output hang never
Last clearing of "show interface" counters 1w3d
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 1152 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
10 input errors, 10 CRC, 0 frame, 0 overrun, 0 ignored, 10 abort
185101 packets output, 2591414 bytes, 0 underruns
0 output errors, 0 collisions, 18509 interface resets
0 output buffer failures, 0 output buffers swapped out
2 carrier transitions
Timeslot(s) Used:1-24, SCC: 1, Transmitter delay is 0 flags
------------------ show controllers ------------------
Interface Serial0/0/0:0
Hardware is GT96Kidb at 0x43178618, driver data structure at 0x42FE357C
wic_info 0x0
Physical Port 0, SCC Num 0
MPSC Registers:
MMCR_L=0x000304C0, MMCR_H=0x00000000, MPCR=0x00000100
CHR1=0x00FE007E, CHR2=0x00000000, CHR3=0x00000648, CHR4=0x00000000
CHR5=0x00000000, CHR6=0x00000000, CHR7=0x00000000, CHR8=0x00000000
CHR9=0x00000000, CHR10=0x00001028
SDMA Registers:
SDC=0x00002201, SDCM=0x00000080
CRDP=0x0FA64900, CTDP=0x0FA64B40, FTDB=0x0FA64B40
Main Routing Register=0x77777711 BRG Conf Register=0x00480000
Rx Clk Routing Register=0x00000000 Tx Clk Routing Register=0x00000000
GPP Registers:
Conf=0x55115511, Io=0x55115511, Data=0xFFFFFFCF, Level=0x00000000
FTDM Registers:
&TCR=0xB400C008, TCR=0x80802500
&tdpram[0]=0xB4008000, tdpram[0]=0xC00FF
&tdpram[1]=0xB4008004, tdpram[1]=0xC01FF
&tdpram[2]=0xB4008008, tdpram[2]=0xC01FF
&tdpram[3]=0xB400800C, tdpram[3]=0xC00FF
&tdpram[4]=0xB4008010, tdpram[4]=0xC00FF
&rdpram[0]=0xB4008400, rdpram[0]=0x20C01FF
&rdpram[1]=0xB4008404, rdpram[1]=0xC01FF
&rdpram[2]=0xB4008408, rdpram[2]=0xC01FF
&rdpram[3]=0xB400840C, rdpram[3]=0xC00FF
&rdpram[4]=0xB4008410, rdpram[4]=0xC01FF
TDM FPGA Registers:
vmcr[0] = 0x00000003, vmcr[1] = 0x00000000,
vmcr[2] = 0x00000000, vmcr[3] = 0x00000000
ntrcr0 = 0x00000000, ntrcr1 = 0x00000000
tdmcr = 0x0000006A, labcr = 0x00000000, tpllr_cr = 0x00000000
nhr = 0x66666626, isr = 0x0000FFFF, imr = 0x00000000
8 input aborts on receiving flag sequence
0 throttles, 0 enables
0 overruns
0 transmitter underruns
0 transmitter CTS losts
8 rxintr, 185101 txintr, 0 rxerr, 0 txerr
20537 mpsc_rx, 0 mpsc_rxerr, 189 mpsc_rlsc, 19320 mpsc_rhnt, 1637 mpsc_rfsc
18515 mpsc_rcsc, 0 mpsc_rovr, 0 mpsc_rcdl, 0 mpsc_rckg, 0 mpsc_bper
0 mpsc_txerr, 0 mpsc_teidl, 0 mpsc_tudr, 0 mpsc_tctsl, 0 mpsc_tckg
0 sdma_rx_sf, 0 sdma_rx_mfl, 0 sdma_rx_or, 8 sdma_rx_abr, 0 sdma_rx_no
0 sdma_rx_de, 0 sdma_rx_cdl, 8 sdma_rx_ce, 0 sdma_tx_rl, 0 sdma_tx_ur
0 sdma_rx_reserr, 0 sdma_tx_reserr
0 rx_bogus_pkts, rx_bogus_flag FALSE
0 sdma_tx_ur_processed
fport 0, 0 ftdm_rint, 0 ftdm_rsl, 0 ftdm_tint, 0 ftdm_tsl
tx_limited = 1(2), errata19 count1 - 0, count2 - 0
Receive Ring
rxr head (0)(0x0FA64900), rxr tail (0)(0x0FA64900)
Interface Serial0/0/1:0
Hardware is GT96Kidb at 0x43180998, driver data structure at 0x42FE58A0
wic_info 0x0
Physical Port 0, SCC Num 1
MPSC Registers:
MMCR_L=0x000304C0, MMCR_H=0x00000000, MPCR=0x00000100
CHR1=0x00FE007E, CHR2=0x00000000, CHR3=0x00000648, CHR4=0x00000000
CHR5=0x00000000, CHR6=0x00000000, CHR7=0x00000000, CHR8=0x00000000
CHR9=0x00000000, CHR10=0x00001028
SDMA Registers:
SDC=0x00002201, SDCM=0x00000080
CRDP=0x0FA7EBC0, CTDP=0x0FA7EE60, FTDB=0x0FA7EE60
Main Routing Register=0x77777711 BRG Conf Register=0x00480000
Rx Clk Routing Register=0x00000000 Tx Clk Routing Register=0x00000000
GPP Registers:
Conf=0x55115511, Io=0x55115511, Data=0xFFFFFFCF, Level=0x00000000
FTDM Registers:
&TCR=0xB400C008, TCR=0x80802500
&tdpram[0]=0xB4008000, tdpram[0]=0xC01FF
&tdpram[1]=0xB4008004, tdpram[1]=0xC01FF
&tdpram[2]=0xB4008008, tdpram[2]=0xC00FF
&tdpram[3]=0xB400800C, tdpram[3]=0xC00FF
&tdpram[4]=0xB4008010, tdpram[4]=0xC01FF
&rdpram[0]=0xB4008400, rdpram[0]=0xC01FF
&rdpram[1]=0xB4008404, rdpram[1]=0xC00FF
&rdpram[2]=0xB4008408, rdpram[2]=0xC01FF
&rdpram[3]=0xB400840C, rdpram[3]=0xC01FF
&rdpram[4]=0xB4008410, rdpram[4]=0xC00FF
TDM FPGA Registers:
vmcr[0] = 0x00000003, vmcr[1] = 0x00000000,
vmcr[2] = 0x00000000, vmcr[3] = 0x00000000
ntrcr0 = 0x00000000, ntrcr1 = 0x00000000
tdmcr = 0x0000006A, labcr = 0x00000000, tpllr_cr = 0x00000000
nhr = 0x66666626, isr = 0x0000FFFF, imr = 0x00000000
10 input aborts on receiving flag sequence
0 throttles, 0 enables
0 overruns
0 transmitter underruns
0 transmitter CTS losts
10 rxintr, 185108 txintr, 0 rxerr, 0 txerr
20393 mpsc_rx, 0 mpsc_rxerr, 174 mpsc_rlsc, 19914 mpsc_rhnt, 1685 mpsc_rfsc
18516 mpsc_rcsc, 0 mpsc_rovr, 0 mpsc_rcdl, 0 mpsc_rckg, 0 mpsc_bper
0 mpsc_txerr, 0 mpsc_teidl, 0 mpsc_tudr, 0 mpsc_tctsl, 0 mpsc_tckg
0 sdma_rx_sf, 0 sdma_rx_mfl, 0 sdma_rx_or, 10 sdma_rx_abr, 0 sdma_rx_no
0 sdma_rx_de, 0 sdma_rx_cdl, 10 sdma_rx_ce, 0 sdma_tx_rl, 0 sdma_tx_ur
0 sdma_rx_reserr, 0 sdma_tx_reserr
0 rx_bogus_pkts, rx_bogus_flag FALSE
0 sdma_tx_ur_processed
fport 0, 0 ftdm_rint, 0 ftdm_rsl, 0 ftdm_tint, 0 ftdm_tsl
tx_limited = 1(2), errata19 count1 - 0, count2 - 0
Receive Ring
------------------ show controllers t1 ------------------
T1 0/0/0 is up.
Applique type is Channelized T1
Cablelength is long gain36 0db
No alarms detected.
alarm-trigger is not set
Version info Firmware: 20040202, FPGA: 11
Framing is ESF, Line Code is B8ZS, Clock Source is Line.
CRC Threshold is 320. Reported from firmware is 320.
Data in current interval (68 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Total Data (last 24 hours)
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
T1 0/0/1 is up.
Applique type is Channelized T1
Cablelength is long gain36 0db
No alarms detected.
alarm-trigger is not set
Version info Firmware: 20040202, FPGA: 11
Framing is ESF, Line Code is B8ZS, Clock Source is Line.
CRC Threshold is 320. Reported from firmware is 320.
Data in current interval (68 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Total Data (last 24 hours)
0 Line Code Violations, 7 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 7 Degraded Mins,
7 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
------------------ show inventory ------------------
NAME: "2811 chassis", DESCR: "2811 chassis, Hw Serial#: FTX0933A11M, Hw Revision: 53.49"
PID: CISCO2811 , VID: V01 , SN: FTX0933A11M
NAME: "c2811 Motherboard with 2FE and integrated VPN", DESCR: "c2811 Motherboard with 2FE and integrated VPN"
PID: CISCO2811 , VID: V01 , SN: FOC09282UEA
NAME: "Two port T1 voice interface daughtercard", DESCR: "Two port T1 voice interface daughtercard"
PID: @%^Yt , VID: , SN: 33947792
|
Answer : Problems with Bonded T-1
|
|
>ip route 0.0.0.0 0.0.0.0 12.124.244.250
OOPS... should be .25 ====
ip route 0.0.0.0 0.0.0.0 12.124.244.25
|
|
|
|
|
