I uploaded the image in the Cisco 1700 from c1700-y-mz.122-4.YA2.bin to c1700-y-mz.122-4.YA6.bin.
But I started getting the error "Serial0/0 is up, line protocol is down" on the router 2600 which has a serial link to the 1700 on which we did the upgrade.
1700 was in a remote location, so we brought it in our office and it came up in "rommon" mode. I erased the flsh, brought in c1700-y-mz.122-4.YA6.bin via tftp.
I have the following 2 questions:
1. How do I check what versions of IOs are compatible wiht my WAN card.
2. How do I make the router take this configuration on startup as everytime I reset the router, it comesup in rommon mode adn I have to mannually boot it form the configuration file.
The following outputs (sh diag nad sh ver) might be helpful:
Router#sh diag
Slot 0:
C1721 1FE Mainboard Port adapter, 2 ports
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 1.0
PCB Serial Number : FOC07240KBR
Part Number : 73-7546-01
Board Revision : A0
Fab Version : 04
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 03 5A 41 01 00 C1 8B 46 4F 43 30 37 32
0x10: 34 30 4B 42 52 82 49 1D 7A 01 42 41 30 02 04 FF
0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
WIC Slot 0:
FT1
Hardware revision 1.5 Board revision G0
Serial number 0030520391 Part number 800-03279-04
Test history 0x00 RMA number 00-00-00
Connector type WAN Module
EEPROM format version 2
EEPROM contents (hex):
0x20: 02 11 01 05 01 D1 B4 47 50 0C CF 04 00 00 00 00
0x30: 80 00 00 00 03 05 07 01 FF FF FF FF FF FF FF FF
Router#sh ver
Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-Y-M), Version 12.2(4)YA6, EARLY DEPLOYMENT RELEAS
E SOFTWARE (fc1)
Synched to technology version 12.2(5.4)T
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Wed 23-Jul-03 19:38 by ealyon
Image text-base: 0x80008124, data-base: 0x807983C0
ROM: System Bootstrap, Version 12.2(7r)XM1, RELEASE SOFTWARE (fc1)
ROM: C1700 Software (C1700-Y-M), Version 12.2(4)YA6, EARLY DEPLOYMENT RELEASE SO
FTWARE (fc1)
Router uptime is 6 minutes
System returned to ROM by power-on
System image file is "flash:c1700-y-mz.122-4.YA6.bin"
cisco 1721 (MPC860P) processor (revision 0x100) with 29492K/3276K bytes of memor
y.
Processor board ID FOC07240KBR (2841942417), with hardware revision 0000
MPC860P processor: part number 5, mask 2
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
WIC T1-DSU
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
Configuration register is 0x8002
|
